Kti-networks KF221TX/3 Uživatelský manuál Strana 1

24Installation Guide10/100 Fast Ethernet AdaptersDOC.991105-KF221TX/3-KP/N:750-0132-001KF-221TX/3

63. Installing the AdapterThis chapter describes how to install the Fast Ethernet PCI adapterin a PCI computer and how to connect the adapter to the n

75. Insert the adapter into the slot and secure the screw (see Figure 3-1).6. Install the WOL cable, if necessary. Refer to 3.2 for the details.7. Rep

8Figure 3-2 PME Jumper JP1 Setting4. Locate the 3-Pin WOL connector on the system motherboard.5. Plug one end of the WOL cable to the 3-Pin WOL connec

93.3 Connecting to the NetworkThe rear bracket of the Fast Ethernet adapter contains one RJ-45connector. The connector is used for either 100Mbps 100B

1010 Mbps ConnectionFor 10BASE-T Ethernet networks, the Fast Ethernet adapter usesCategory 3, 4, or 5 UTP cable. To establish a valid 10 Mbps connec-t

11100 Mbps ConnectionFor 100BASE-TX Fast Ethernet networks, the adapter supportsCategory 5 UTP cabling. To establish a valid 100 Mbps connection,

124. Network Driver InstallationAfter making the connection to the network, you must install theadapter network driver in order to connect the Fast Et

13In addition to the basic drivers, more updated information and driv-ers may be included in the driver media after this guide is published.Please ref

144.3 Installation for Windows 98 SystemAfter the driver installation for Windows 98, there are some simplemethods to check the installation is proper

15The adapter name shown in Device Manager should be "KF221TXFast Ethernet PCI Adapter". The installation is proper if there is no"?&qu

25 1999, KTI Networks Inc. All rights reserved. No part of thisdocumentation may be reproduced in any form or by any means orused to make any direc

165. LED IndicatorsEach Fast Ethernet adapter has three LEDs, as shown in Figure 1-2.5.1 InterpretationsThe interpretations of the LEDs are:100Mb LED

17AppendixA1. SpecificationsNetwork std.: 10 MbpsIEEE 802.3 10BASE-T Ethernet100 Mbps IEEE 802.3u 100BASE-TX Fast EthernetSpeed : Auto-sense, auto-neg

18A.2 Auto-negotiation FunctionThe adapter is equipped with an auto-negotiation function. Auto-negotiation is a negotiation procedure between two conn

19A.3 Installing Remote Boot ROMBefore you can use the remote boot function, you have to setup theremote boot service on the file server and install t

23TRADEMARKSEthernet is a registered trademark of Xerox Corp. NetWare is a registered trademark ofNovell Inc. Intel, Microsoft, Toshiba are trademarks

21Table of Contents1. Introduction1.1 Adapter Features ... 11.2 Connectors and LEDs...

11. IntroductionThe 10/100BASE-TX Fast Ethernet PCI Adapter is a 32-bit LANadapter for use in personal computers with PCI computer bus slots.This adap

21.2 Connectors and LEDsFigure 1-1 shows the important components on the adapter.No. Components Description1 Intel 21143 LAN controller2 JP2 3-Pin Wa

3Figure 1-2 shows the connector and LEDs on the bracket.No. Components Description1 10/100 Mbps This RJ-45 connector requires UTPnetwork connector cab

42. Wake on LAN TechnologyThe adapter is an ACPI-compliant network adapter that supportsthe following features:_ Power management interface_ Remote wa

5WOL InstallationThe adapter features :1. One LAN controller which can support PCI power manage-ment interface and function.2. One 3-Pin Wake on LAN (